Stainless steel slot drains light load – with inner width 65 mm model SPK
Spout on one side descending on spout.
Drainage pit with odor trap
Center drain descending to the spout.
Drainage pit with odor trap.
T-shaped drains
center drain – descending to the drain.
Drainage pit with odor trap.
Spout descending from an angle at the spout.
Drainage pit with odor trap.
Two or more drains
with odor lock each from point
descend to the drain.
STANDARD FEATURES
- With a drain with a minimum depth of 65 mm and a maximum depth of 200 mm, it is possible to build a continuous continuous waste water drainage system with a maximum length of 18000 mm, with a constant slope of 0.6% towards the drain.
- The trenches can be made to the desired dimensions, provided that they meet the slope, minimum and maximum depth.
- By reducing the slope of the drain, it is possible to construct a trench up to a maximum length of 70.00 meters.
- By using several drainage pits, it is possible to construct a trench of several meters.
- A reinforcement has been applied to the upper surface of the trench with a mutual distance of 500 mm.
- The slot drain is provided on both sides with adjustable feet and anchorage strips with a mutual distance of 500 mm. This allows the trench to be attached to a concrete surface and adjusted in height.
- The trench with a plate thickness of 2.00 mm is provided with a flange of 5.00 mm. This is provided with a gasket and is attached with bolt and nut. The bolt and nut are made of 18/8 Cr / NI (AISI 304 quality).
OPTIONS
- On request, this drain system can be made of stainless steel AISI 316 quality.
- A PVC or stainless steel filler profile can be used to simplify assembly and to strengthen the load-bearing capacity of the upper profile.
I want more information and advice?
Phone number : +90 (0) 549 276 59 54
E-mail : info@fenicromdrain.com
Stainless steel slot drains heavy load – with inner width 100 mm model TMP
Spout on one side descending on spout.
Drainage pit with odor trap.
Center drain descending to the spout.
Drainage pit with odor trap
T-shaped drains
center drain – descending to the drain.
Drainage pit with odor trap.
Spout descending from an angle at the spout.
Drainage pit with odor trap.
Two or more drains
with odor lock each from point
descend to the drain.
STANDARD FEATURES
- With a channel with a minimum depth of 95 mm and a maximum depth of 200 mm, it is possible to build a continuous waste water drainage system with a maximum length of 18000 mm, with a constant slope of 0.6% towards the drain.
- The trenches can be made to the desired dimensions, provided that they meet the slope, minimum and maximum depth.
- By reducing the slope of the gutter, it is possible to construct a trench up to a maximum length of 70.00 meters.
- By using several floor drains, it is possible to construct a trench of several meters.
- The slot channel is provided on both sides with adjustbale feet and anchorage strips with a mutual distance of 500 mm. This allows the trench to be attached to a concrete surface and adjusted in height.
- The drains with a plate thickness of 2.00 mm is provided with a flange of 35.00 mm. This is provided with a gasket and is attached with bolt and nut. The bolt and nut are made of 18/8 Cr / NI (AISI 304 quality).
OPTIONS
- On request, this drain system can be made of stainless steel AISI 316 quality.
- A PVC or stainless steel filler profile can be used to simplify assembly and to strengthen the load-bearing capacity of the upper profile.
I want more information and advice?
Phone number : +90 (0) 549 276 59 54
E-mail : info@fenicromdrain.com
Stainless steel slot drains isolated light load – with inner width 65 mm model ISPK
Suitable for chemical resistant flooring and concrete floors
Spout on one side descending on spout.
Drainage pit with odor trap.
Center drain descending to the spout.
Drainage pit with odor trap.
T-shaped drains
center drain – descending to the drain.
Drainage pit with odor trap.
Spout descending from an angle at the spout.
Drainage pit with odor trap.
Two or more drains
with odor lock each from point
descend to the drain.
Stainless steel slot drains isolated light load
STANDARD FEATURES
- With a channel with a minimum depth of 75 mm and a maximum depth of 200 mm, it is possible to build a continuous waste water drainage system with a maximum length of 18000 mm, with a constant slope of 0.6% towards the drain.
- The trenches can be made to the desired dimensions, provided that they meet the slope, minimum and maximum depth.
- By reducing the slope of the gutter, it is possible to construct a trench up to a maximum length of 70.00 meters.
- By using several floor drains, it is possible to construct a trench of several meters.
- The slot channel is provided on both sides with adjustable feet and anchorage strips with a mutual distance of 500 mm. This allows the trench to be attached to a concrete surface and adjusted in height.
- The drains with a plate thickness of 2.00 mm is provided with a flange of 35.00 mm. This is provided with a gasket and is attached with bolt and nut. The bolt and nut are made of 18/8 Cr / NI (AISI 304 quality).
OPTIONS
- On request, this drain system can be made of stainless steel AISI 316 quality.
- A PVC or stainless steel filler profile can be used to simplify assembly and to strengthen the load-bearing capacity of the upper profile.
Projects
I want more information and advice?
Phone number : +90 (0) 549 276 59 54
E-mail : info@fenicromdrain.com
Stainless steel slot drains isolated heavy load – with inner width 100 mm with double flange model ITMP
Suitable for chemical resistant flooring and concrete floors
Spout on one side descending on spout.
Drainage pit with odor trap.
Center drain descending to the spout.
Drainage pit with odor trap.
T-shaped drains
center drain – descending to the drain.
Drainage pit with odor trap.
Spout descending from an angle at the spout.
Drainage pit with odor trap.
Two or more drains
with odor lock each from point
descend to the drain.
Stainless steel slot drains isolated heavy duty
STANDARD FEATURES
- With a channel with a minimum depth of 105 mm and a maximum depth of 200 mm, it is possible to build a continuous waste water drainage system with a maximum length of 18000 mm, with a constant slope of 0.6% towards the drain.
- The trenches can be made to the desired dimensions, provided that they meet the slope, minimum and maximum depth.
- By reducing the slope of the gutter, it is possible to construct a trench up to a maximum length of 70.00 meters.
- By using several floor drains, it is possible to construct a trench of several meters.
- The slot channel is provided on both sides with adjustable feet and anchorage strips with a mutual distance of 500 mm. This allows the trench to be attached to a concrete surface and adjusted in height.
- The drains with a plate thickness of 2.00 mm is provided with a flange of 35.00 mm. This is provided with a gasket and is attached with bolt and nut. The bolt and nut are made of 18/8 Cr / NI (AISI 304 quality).
OPTIONS
- On request, this drain system can be made of stainless steel AISI 316 quality.
- A PVC or stainless steel filler profile can be used to simplify assembly and to strengthen the load-bearing capacity of the upper profile.
Projets
I want more information and advice?
Phone number : +90 (0) 549 276 59 54
E-mail : info@fenicromdrain.com